integration unavailable every couple of minutes

[Hugyleviking]

System Health details

Home assitant up to date et flashforge integration 1.0.5

Checklist

• I have enabled debug logging for my installation.
• I have filled out the issue template to the best of my ability.
• This issue only contains 1 issue (if you have multiple issues, open one issue for each issue).
• This issue is not a duplicate issue of currently previous issues..

Describe the issue

Hello,

integration becomes unavailable after a few minutes and then available again? The cycle is infinite.

Reproduction steps

1. Begin to print
2. Integration available
3. Few minutes later integration unavailable
   ... 30 seconds later integration available

infinite loop

Debug logs

2024-04-29 20:50:38.621 DEBUG (MainThread) [custom_components.flashforge.data_update_coordinator] Finished fetching FlashForge-55af99e92e479bd721455a08ff1c89b7 data in 0.006 seconds (success: True)
2024-04-29 20:51:08.621 ERROR (MainThread) [custom_components.flashforge.data_update_coordinator] Error fetching FlashForge-55af99e92e479bd721455a08ff1c89b7 data: [Errno 104] Connection reset by peer
2024-04-29 20:51:08.622 DEBUG (MainThread) [custom_components.flashforge.data_update_coordinator] Finished fetching FlashForge-55af99e92e479bd721455a08ff1c89b7 data in 0.007 seconds (success: False)
2024-04-29 20:51:09.598 WARNING (SyncWorker_63) [custom_components.flashforge.camera] Unable to get still image when Adventurer 5M Camera camera is offline
2024-04-29 20:51:19.596 WARNING (SyncWorker_47) [custom_components.flashforge.camera] Unable to get still image when Adventurer 5M Camera camera is offline
2024-04-29 20:51:29.596 WARNING (SyncWorker_35) [custom_components.flashforge.camera] Unable to get still image when Adventurer 5M Camera camera is offline
2024-04-29 20:51:38.629 INFO (MainThread) [custom_components.flashforge.data_update_coordinator] Fetching FlashForge-55af99e92e479bd721455a08ff1c89b7 data recovered
2024-04-29 20:51:38.629 DEBUG (MainThread) [custom_components.flashforge.data_update_coordinator] Finished fetching FlashForge-55af99e92e479bd721455a08ff1c89b7 data in 0.015 seconds (success: True)

Diagnostics dump

No response

[Hugyleviking]

Error with Flashforge firmware 2.4.5 and 2.6.6

[Hugyleviking]

?

[Hugyleviking]

Any other people have this problem ?

[joseffallman]

Hi, sorry for the delay.
No I haven't experience this. Perhaps because I haven't print that much in the latest :)
This could be of multiple reasons, hard to tell if it's the integration in home assistant or your network setup.
I have a Adventure 4 on firmware v2.2.4 that is won't update because the issues in newer firmware. Therefore it will be hard for me to investigate any further in this.
When it happens, are you having any other software that's connected to the printer, like flashprint. Is it the same if you close it down? Is the printer connected through wifi or ethernet?

[Hugyleviking]

When problem happend, no network problem and my printer ping is ok during the Home Assistant integration said unaivalable. My printer is connected with ethernet cable.

[joseffallman]

I started to encounter this myself.
Sometimes after a couple of minutes the printer disconnects from wifi. This could be related to how often information is read out from printer.
I will see if i could tweak a little. But it's hard to troubleshoot when it only happens sometimes.

[MikeVRT]

Still the same for v0.1.5
To repeat the issue, you don't need to print. Just switch the printer on and wait for a while.

Printer:

• A5M Pro
• FW 2.7.6-2.2.3
• Connected via RJ45, no connection issues observed

HA:

• Core 2024.11.3
• Supervisor 2024.11.4
• Operating System 12.4
• Frontend 20241106.2

[N3rd7]

I also experience this regularly, but I don't have the knowledge to troubleshoot or help finding a solution. Let me know if there is something I can try on my end.
Printer AD5M connected via ethernet cable
Home assistant OS running on Raspi5, latest updates installed.