adafruit_mlx90393.py

# SPDX-FileCopyrightText: 2018 Kevin Townsend for Adafruit Industries
#
# SPDX-License-Identifier: MIT

"""
`adafruit_mlx90393`
====================================================

This is a breakout for the Adafruit MLX90393 magnetometer sensor breakout.

* Author(s): ktown

Implementation Notes
--------------------

**Hardware:**

* Adafruit `MLX90393 Magnetometer Sensor Breakout Board
  <https://www.adafruit.com/product/4022>`_ (Product ID: 4022)

**Software and Dependencies:**

* Adafruit CircuitPython firmware for the supported boards:
  https://circuitpython.org/downloads
* Adafruit's Bus Device library:
  https://github.com/adafruit/Adafruit_CircuitPython_BusDevice
* Adafruit's Register library:
  https://github.com/adafruit/Adafruit_CircuitPython_Register

"""

import struct
import time

from adafruit_bus_device.i2c_device import I2CDevice
from micropython import const

try:
    from typing import Tuple

    from busio import I2C
    from circuitpython_typing import ReadableBuffer
except ImportError:
    pass

__version__ = "0.0.0+auto.0"
__repo__ = "https://github.com/adafruit/Adafruit_CircuitPython_MLX90393.git"

_CMD_SB = const(0b00010000)  # Start burst mode
_CMD_SW = const(0b00100000)  # Start wakeup on change mode
_CMD_SM = const(0b00110000)  # Start single-measurement mode
_CMD_RM = const(0b01000000)  # Read measurement
_CMD_RR = const(0b01010000)  # Read register
_CMD_WR = const(0b01100000)  # Write register
_CMD_EX = const(0b10000000)  # Exit mode
_CMD_HR = const(0b11010000)  # Memory recall
_CMD_HS = const(0b11100000)  # Memory store
_CMD_RT = const(0b11110000)  # Reset
_CMD_NOP = const(0x00)  # NOP

_CMD_AXIS_ALL = const(0xE)  # X+Y+Z axis bits for commands
_CMD_TEMP = const(0x01)  # Temperature bit for commands

_CMD_REG_CONF1 = const(0x00)  # Gain
_CMD_REG_CONF2 = const(0x01)  # Burst, comm mode, temperature compensation
_CMD_REG_CONF3 = const(0x02)  # Oversampling, Filter, Resolution
_CMD_REG_CONF4 = const(0x03)  # Sensitivity drift
_CMD_REG_CONF5 = const(0x04)  # X-axis Offset Correction
_CMD_REG_CONF6 = const(0x05)  # Y-axis Offset Correction
_CMD_REG_CONF7 = const(0x06)  # Z-axis Offset Correction

# Gain settings
GAIN_5X = 0x0
GAIN_4X = 0x1
GAIN_3X = 0x2
GAIN_2_5X = 0x3
GAIN_2X = 0x4
GAIN_1_67X = 0x5
GAIN_1_33X = 0x6
GAIN_1X = 0x7
_GAIN_SHIFT = const(4)

# Resolution settings
RESOLUTION_16 = 0x0
RESOLUTION_17 = 0x1
RESOLUTION_18 = 0x2
RESOLUTION_19 = 0x3

# Filter settings
FILTER_0 = 0x0
FILTER_1 = 0x1
FILTER_2 = 0x2
FILTER_3 = 0x3
FILTER_4 = 0x4
FILTER_5 = 0x5
FILTER_6 = 0x6
FILTER_7 = 0x7

# Oversampling settings
OSR_0 = 0x0
OSR_1 = 0x1
OSR_2 = 0x2
OSR_3 = 0x3

# Hall plate spinning rate adjustment
# Must be 0x0C (default) or 0x00
_HALLCONF = const(0x0C)

STATUS_OK = 0x3

# The lookup table below allows you to convert raw sensor data to uT
# using the appropriate (gain/resolution-dependant) lsb-per-uT
# coefficient below. Note that the z axis has a different coefficient
# than the x and y axis.
_LSB_LOOKUP = (
    # HALLCONF = 0x0C (default)
    (
        # 5x gain: res0(xy)(z), res1(xy)(z), res2(xy)(z), res3(xy)(z)
        ((0.751, 1.210), (1.502, 2.420), (3.004, 4.840), (6.009, 9.680)),
        # 4x gain: res0(xy)(z), res1(xy)(z), res2(xy)(z), res3(xy)(z)
        ((0.601, 0.968), (1.202, 1.936), (2.403, 3.872), (4.840, 7.744)),
        # 3x gain: res0(xy)(z), res1(xy)(z), res2(xy)(z), res3(xy)(z)
        ((0.451, 0.726), (0.901, 1.452), (1.803, 2.904), (3.605, 5.808)),
        # 2.5x gain: res0(xy)(z), res1(xy)(z), res2(xy)(z), res3(xy)(z)
        ((0.376, 0.605), (0.751, 1.210), (1.502, 2.420), (3.004, 4.840)),
        # 2x gain: res0(xy)(z), res1(xy)(z), res2(xy)(z), res3(xy)(z)
        ((0.300, 0.484), (0.601, 0.968), (1.202, 1.936), (2.403, 3.872)),
        # 1.667x gain: res0(xy)(z), res1(xy)(z), res2(xy)(z), res3(xy)(z)
        ((0.250, 0.403), (0.501, 0.807), (1.001, 1.613), (2.003, 3.227)),
        # 1.333x gain: res0(xy)(z), res1(xy)(z), res2(xy)(z), res3(xy)(z)
        ((0.200, 0.323), (0.401, 0.645), (0.801, 1.291), (1.602, 2.581)),
        # 1x gain: res0(xy)(z), res1(xy)(z), res2(xy)(z), res3(xy)(z)
        ((0.150, 0.242), (0.300, 0.484), (0.601, 0.968), (1.202, 1.936)),
    ),
    # HALLCONF = 0x00
    (
        # GAIN_SEL = 0, 5x gain
        ((0.787, 1.267), (1.573, 2.534), (3.146, 5.068), (6.292, 10.137)),
        # GAIN_SEL = 1, 4x gain
        ((0.629, 1.014), (1.258, 2.027), (2.517, 4.055), (5.034, 8.109)),
        # GAIN_SEL = 2, 3x gain
        ((0.472, 0.760), (0.944, 1.521), (1.888, 3.041), (3.775, 6.082)),
        # GAIN_SEL = 3, 2.5x gain
        ((0.393, 0.634), (0.787, 1.267), (1.573, 2.534), (3.146, 5.068)),
        # GAIN_SEL = 4, 2x gain
        ((0.315, 0.507), (0.629, 1.014), (1.258, 2.027), (2.517, 4.055)),
        # GAIN_SEL = 5, 1.667x gain
        ((0.262, 0.422), (0.524, 0.845), (1.049, 1.689), (2.097, 3.379)),
        # GAIN_SEL = 6, 1.333x gain
        ((0.210, 0.338), (0.419, 0.676), (0.839, 1.352), (1.678, 2.703)),
        # GAIN_SEL = 7, 1x gain
        ((0.157, 0.253), (0.315, 0.507), (0.629, 1.014), (1.258, 2.027)),
    ),
)

# Lookup table for conversion times for different filter and
# oversampling settings. Values taken from datasheet.
_TCONV_LOOKUP = (
    # OSR = 0      1       2       3
    (1.27, 1.84, 3.00, 5.30),  # DIG_FILT = 0
    (1.46, 2.23, 3.76, 6.84),  # DIG_FILT = 1
    (1.84, 3.00, 5.30, 9.91),  # DIG_FILT = 2
    (2.61, 4.53, 8.37, 16.05),  # DIG_FILT = 3
    (4.15, 7.60, 14.52, 28.34),  # DIG_FILT = 4
    (7.22, 13.75, 26.80, 52.92),  # DIG_FILT = 5
    (13.36, 26.04, 51.38, 102.07),  # DIG_FILT = 6
    (25.65, 50.61, 100.53, 200.37),  # DIF_FILT = 7
)


class MLX90393:  # pylint: disable=too-many-instance-attributes
    """
    Driver for the MLX90393 magnetometer.

    :param i2c_bus: The I2C bus the device is connected to
    :param int address: The I2C device address. Defaults to :const:`0x0C`
    :param int gain: The gain level to apply. Defaults to :const:`GAIN_1X`
    :param int resolution: The resolution level to use.  Defaults to :const:`RESOLUTION_16`
    :param int filt: The filter to use. Defaults to :const:`FILTER_7`
    :param int oversampling: The oversampleing setting to use. Defaults to :const:`OSR_3`
    :param bool debug: Enable debug output. Defaults to `False`


    **Quickstart: Importing and using the device**

        Here is an example of using the :class:`MLX90393` class.
        First you will need to import the libraries to use the sensor

        .. code-block:: python

            import board
            import adafruit_mlx90393

        Once this is done you can define your `board.I2C` object and define your sensor object

        .. code-block:: python

            i2c = board.I2C()  # uses board.SCL and board.SDA
            SENSOR = adafruit_mlx90393.MLX90393(i2c)

        Now you have access to the :attr:`magnetic` attribute

        .. code-block:: python

            MX, MY, MZ = SENSOR.magnetic

    """

    def __init__(  # pylint: disable=too-many-arguments
        self,
        i2c_bus: I2C,
        address: int = 0x0C,
        gain: int = GAIN_1X,
        resolution: int = RESOLUTION_16,
        filt: int = FILTER_7,
        oversampling: int = OSR_3,
        temperature_compensation: bool = False,
        offset: int = 0,
        debug: bool = False,
    ) -> None:
        self.i2c_device = I2CDevice(i2c_bus, address)
        self._debug = debug
        self._status_last = 0
        self._res_x = self._res_y = self._res_z = resolution
        self._filter = filt
        self._osr = oversampling
        self._gain_current = gain
        self._temperature_compensation = temperature_compensation
        self._off_x = self._off_y = self._off_z = offset

        # Put the device in a known state to start
        self.reset()

        # Set resolution to the supplied level
        self.resolution_x = self._res_x
        self.resolution_y = self._res_y
        self.resolution_z = self._res_z

        # Set filter to the supplied level
        self.filter = self._filter

        # Set oversampling to the supplied level
        self.oversampling = self._osr

        # Set gain to the supplied level
        self.gain = self._gain_current
        self.temperature_compensation = self._temperature_compensation

        # Set offsets to supplied level
        self.offset_x = self._off_x
        self.offset_y = self._off_y
        self.offset_z = self._off_z

    def _transceive(self, payload: ReadableBuffer, rxlen: int = 0) -> bytearray:
        """
        Writes the specified 'payload' to the sensor
        Returns the results of the write attempt.

        :param ReadableBuffer payload: The byte array to write to the sensor
        :param int rxlen: numbers of bytes to read back. Defaults to :const:`0`

        """
        # Read the response (+1 to account for the mandatory status byte!)
        data = bytearray(rxlen + 1)

        if len(payload) == 1:
            # Transceive with repeated start
            with self.i2c_device as i2c:
                i2c.write_then_readinto(payload, data)
        else:
            # Write 'value' to the specified register
            # TODO: Check this. It's weird that the write is accepted but the read is naked.
            with self.i2c_device as i2c:
                i2c.write(payload)

                while True:
                    try:
                        i2c.readinto(data)
                        if data[0]:
                            break
                    except OSError:
                        pass

        # Track status byte
        self._status_last = data[0]
        # Unpack data (status byte, big-endian 16-bit register value)
        if self._debug:
            print("\t[{}]".format(time.monotonic()))
            print("\t Writing :", [hex(b) for b in payload])
            print("\tResponse :", [hex(b) for b in data])
            print("\t  Status :", hex(data[0]))
        return data

    @property
    def last_status(self) -> int:
        """
        The last status byte received from the sensor.
        """
        return self._status_last

    @property
    def gain(self) -> int:
        """
        The gain setting for the device.
        """
        return self._gain_current

    @gain.setter
    def gain(self, value: int) -> None:
        if value > GAIN_1X or value < GAIN_5X:
            raise ValueError("Invalid GAIN setting")
        if self._debug:
            print("\tSetting gain: {}".format(value))
        self._gain_current = value
        self._transceive(
            bytes(
                [
                    _CMD_WR,
                    0x00,
                    self._gain_current << _GAIN_SHIFT | _HALLCONF,
                    (_CMD_REG_CONF1 & 0x3F) << 2,
                ]
            )
        )

    @property
    def resolution_x(self) -> int:
        """The X axis resolution."""
        return self._res_x

    @resolution_x.setter
    def resolution_x(self, resolution: int) -> None:
        self._set_resolution(0, resolution)
        self._res_x = resolution

    @property
    def resolution_y(self) -> int:
        """The Y axis resolution."""
        return self._res_y

    @resolution_y.setter
    def resolution_y(self, resolution: int) -> None:
        self._set_resolution(1, resolution)
        self._res_y = resolution

    @property
    def resolution_z(self) -> int:
        """The Z axis resolution."""
        return self._res_z

    @resolution_z.setter
    def resolution_z(self, resolution: int) -> None:
        self._set_resolution(2, resolution)
        self._res_z = resolution

    def _set_resolution(self, axis: int, resolution: int) -> None:
        if resolution not in (
            RESOLUTION_16,
            RESOLUTION_17,
            RESOLUTION_18,
            RESOLUTION_19,
        ):
            raise ValueError("Incorrect resolution setting.")
        shift = (5, 7, 9)[axis]
        mask = (0xFF9F, 0xFE7F, 0xF9FF)[axis]
        reg = self.read_reg(_CMD_REG_CONF3)
        reg &= mask
        reg |= (resolution & 0x3) << shift
        self.write_reg(_CMD_REG_CONF3, reg)

    @property
    def filter(self) -> int:
        """The filter level."""
        return self._filter

    @filter.setter
    def filter(self, level: int) -> None:
        if level not in range(8):
            raise ValueError("Incorrect filter level.")
        reg = self.read_reg(_CMD_REG_CONF3)
        reg &= 0xFFE3
        reg |= (level & 0x7) << 2
        self.write_reg(_CMD_REG_CONF3, reg)
        self._filter = level

    @property
    def oversampling(self) -> int:
        """The oversampling level."""
        return self._osr

    @oversampling.setter
    def oversampling(self, level: int) -> None:
        if level not in range(4):
            raise ValueError("Incorrect oversampling level.")
        reg = self.read_reg(_CMD_REG_CONF3)
        reg &= 0xFFFC
        reg |= level & 0x3
        self.write_reg(_CMD_REG_CONF3, reg)
        self._osr = level

    @property
    def temperature_compensation(self) -> bool:
        """The temperature compensation setting"""
        return self._temperature_compensation

    @temperature_compensation.setter
    def temperature_compensation(self, temperature_compensation: bool) -> None:
        reg = self.read_reg(_CMD_REG_CONF2)
        t_cmp_bit = 10
        reg &= ~(1 << t_cmp_bit)
        reg |= temperature_compensation << t_cmp_bit
        self.write_reg(_CMD_REG_CONF2, reg)
        self._temperature_compensation = temperature_compensation

    @property
    def offset_x(self) -> int:
        """The X axis offset."""
        return self._off_x

    @offset_x.setter
    def offset_x(self, offset: int) -> None:
        self._set_offset(0, offset)
        self._off_x = offset

    @property
    def offset_y(self) -> int:
        """The Y axis offset."""
        return self._off_y

    @offset_y.setter
    def offset_y(self, offset: int) -> None:
        self._set_offset(1, offset)
        self._off_y = offset

    @property
    def offset_z(self) -> int:
        """The Z axis offset."""
        return self._off_z

    @offset_z.setter
    def offset_z(self, offset: int) -> None:
        self._set_offset(2, offset)
        self._off_z = offset

    def _set_offset(self, axis: int, offset: int) -> None:
        if offset < 0x0000 or offset > 0xFFFF:
            raise ValueError("Incorrect offset setting.")
        if axis == 0:
            self.write_reg(_CMD_REG_CONF5, offset)
        elif axis == 1:
            self.write_reg(_CMD_REG_CONF6, offset)
        elif axis == 2:
            self.write_reg(_CMD_REG_CONF7, offset)
        else:
            raise ValueError("Incorrect axis setting.")

    def display_status(self) -> None:
        """
        Prints out the content of the last status byte in a human-readable
        format.
        """
        avail = 0
        if self._status_last & 0b11 > 0:
            avail = 2 * (self._status_last & 0b11) + 2
        print("STATUS register = 0x{0:02X}".format(self._status_last))
        print("BURST Mode               :", (self._status_last & (1 << 7)) > 0)
        print("WOC Mode                 :", (self._status_last & (1 << 6)) > 0)
        print("SM Mode                  :", (self._status_last & (1 << 5)) > 0)
        print("Error                    :", (self._status_last & (1 << 4)) > 0)
        print("Single error detection   :", (self._status_last & (1 << 3)) > 0)
        print("Reset status             :", (self._status_last & (1 << 2)) > 0)
        print("Response bytes available :", avail)

    def read_reg(self, reg: int) -> int:
        """
        Gets the current value of the specified register.

        :param int reg: The register to read
        """
        # Read register
        payload = bytes([_CMD_RR, reg << 2])
        data = bytearray(3)
        with self.i2c_device as i2c:
            i2c.write_then_readinto(payload, data)

        # Unpack data (status byte, big-endian 16-bit register value)
        self._status_last, val = struct.unpack(">BH", data)
        if self._debug:
            print("\t[{}]".format(time.monotonic()))
            print("\t Writing :", [hex(b) for b in payload])
            print("\tResponse :", [hex(b) for b in data])
            print("\t  Status :", hex(data[0]))
        return val

    def write_reg(self, reg: int, value: int) -> None:
        """
        Writes the 16-bit value to the supplied register.

        :param int reg: The register to write to
        :param int value: The value to write to the register
        """
        self._transceive(
            bytes(
                [
                    _CMD_WR,
                    value >> 8,  # high byte
                    value & 0xFF,  # low byte
                    reg << 2,  # the register
                ]
            )
        )

    def reset(self) -> None:
        """
        Performs a software reset of the sensor.
        """
        self._transceive(bytes([_CMD_EX]))
        if self._debug:
            print("Resetting sensor")
        time.sleep(0.002)
        self._transceive(bytes([_CMD_RT]))
        # burn a read post reset
        try:
            self.magnetic
        except OSError:
            pass
        return self._status_last

    @property
    def read_data(self) -> Tuple[int, int, int]:
        """
        Reads a single X/Y/Z sample from the magnetometer.
        """

        resolutions = {self.resolution_x, self.resolution_y, self.resolution_z}
        valid_tcomp_resolutions = {RESOLUTION_16, RESOLUTION_17}
        if self._temperature_compensation and not resolutions.issubset(
            valid_tcomp_resolutions
        ):
            resolutions_output = f"""Current Resolutions:
\tresolution_x: {self.resolution_x}
\tresolution_y: {self.resolution_y}
\tresolution_z: {self.resolution_z}"""

            raise ValueError(
                "All resolutions must be RESOLUTION_16 or RESOLUTION_17"
                f" if temperature compensation is enabled.\n {resolutions_output}"
            )

        # Set conversion delay based on filter and oversampling
        delay = _TCONV_LOOKUP[self._filter][self._osr] / 1000  # per datasheet
        delay *= 1.1  # plus a little

        # Set the device to single measurement mode
        self._transceive(bytes([_CMD_SM | _CMD_AXIS_ALL]))

        # Insert a delay since we aren't using INTs for DRDY
        time.sleep(delay)

        # Read the 'XYZ' data
        data = self._transceive(bytes([_CMD_RM | _CMD_AXIS_ALL]), 6)

        # Unpack status and raw int values
        self._status_last = data[0]
        m_x = self._unpack_axis_data(self._res_x, data[1:3])
        m_y = self._unpack_axis_data(self._res_y, data[3:5])
        m_z = self._unpack_axis_data(self._res_z, data[5:7])

        # Return the raw int values if requested
        return m_x, m_y, m_z

    # pylint: disable=no-self-use
    def _unpack_axis_data(self, resolution: int, data: ReadableBuffer) -> int:
        # see datasheet
        if resolution == RESOLUTION_19:
            (value,) = struct.unpack(">H", data)
            value -= 0x4000
        elif resolution == RESOLUTION_18:
            (value,) = struct.unpack(">H", data)
            value -= 0x8000
        elif self.temperature_compensation:
            (value,) = struct.unpack(">H", data)
            value -= 0x8000
        else:
            value = struct.unpack(">h", data)[0]
        return value

    @property
    def magnetic(self) -> Tuple[float, float, float]:
        """
        The processed magnetometer sensor values.
        A 3-tuple of X, Y, Z axis values in microteslas that are signed floats.
        """
        x, y, z = self.read_data

        # Check for valid HALLCONF value and set _LSB_LOOKUP index
        if _HALLCONF == 0x0C:
            hallconf_index = 0
        elif _HALLCONF == 0x00:
            hallconf_index = 1
        else:
            raise ValueError("Incorrect HALLCONF value, must be '0x0C' or '0x00'.")

        # Convert the raw integer values to uT based on gain and resolution
        x *= _LSB_LOOKUP[hallconf_index][self._gain_current][self._res_x][0]
        y *= _LSB_LOOKUP[hallconf_index][self._gain_current][self._res_y][0]
        z *= _LSB_LOOKUP[hallconf_index][self._gain_current][self._res_z][1]

        return x, y, z

    @property
    def temperature(self) -> float:
        """
        Reads a single temperature sample from the magnetometer.
        Temperature value in Celsius
        """
        # Read the temperature reference from register 0x24
        treference = self.read_reg(0x24)

        # Value taken from maximum time of temperature conversion on the datasheet section 12.
        # maximum time for temperature conversion = 1603 us
        delay = 0.1

        # Set the device to single measurement mode
        self._transceive(bytes([_CMD_SM | _CMD_TEMP]))

        time.sleep(delay)

        # Read the 'temp' data
        data = self._transceive(bytes([_CMD_RM | _CMD_TEMP]), 2)

        # Unpack status and raw int values
        self._status_last = data[0]

        # from https://www.melexis.com/-/media/files/documents/
        # application-notes/mlx90393-temperature-compensation-application-note-melexis.pdf
        tvalue = struct.unpack(">H", data[1:3])[0]
        # See previous link for conversion formula

        return 35 + ((tvalue - treference) / 45.2)