forked from Klipper3d/klipper
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathprinter-wanhao-duplicator-i3-v2.1-2017.cfg
169 lines (157 loc) · 5.12 KB
/
printer-wanhao-duplicator-i3-v2.1-2017.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
# This file contains pin mappings and other appropriate default
# parameters for a Wanhao Duplicator i3 v2.1 and its clones (Monoprice
# Maker Select, Cocoon Create, etc.).
#
# This will probably work on older revisions (v1.0, v2.0) of the printer
# but is untested on those versions.
# Note, a number of Melzi boards are shipped with a bootloader that
# requires the following command to flash the board:
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
# If the above command does not work and "make flash" does not work
# then one may need to flash a bootloader to the board - see the
# Klipper docs/Bootloaders.md file for more information.
# See the example.cfg file for a description of available parameters.
# For best results with klipper and the Wanhao Duplicator i3, follow these
# guidelines:
#
# - Locate the USB serial port for your printer in /dev/serial/by-id/ format.
# See https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#wheres-my-serial-port
# It will be something like:
# /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_ABCD1234-if00-port0
#
# - Configure klipper to compile firmware for the AVR atmega1284p
#
# - At this point, "make flash FLASH_DEVICE=..." should successfully
# flash your printer board. Use the /dev/serial/by-id/ format for
# FLASH_DEVICE to ensure consistent results.
# See https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#the-make-flash-command-doesnt-work
# if you have problems.
#
# - Copy this sample file you are currently reading to ~/printer.cfg,
# and customize the following parameters:
# * [extruder] > step_distance
#
# This is the inverse of "E steps" (extruder steps per mm) from the stock
# Wanhao Repetier-based firmware.
# (See https://3dprinterwiki.info/extruder-steps/ )
#
# For example, if your E-steps are set to 107.0 steps per mm,
# then step_distance should be (1 / 107.0) ~= .009346
#
# * [extruder] > PID parameters (pid_Kp, pid_Ki, pid_Kd)
# * [heater_bed] > PID parameters (pid_Kp, pid_Ki, pid_Kd)
#
# PID values from stock Wanhao firmware (Repetier) do not
# translate directly to klipper. You will need to run klipper's
# PID autotune function for the extruder and bed. After getting the
# klipper firmware up and running, run the PID_CALIBRATE procedures
# by sending these commands via octoprint terminal (one per autotune):
#
# extruder: PID_CALIBRATE HEATER=extruder TARGET=<temp>
# heated bed: PID_CALIBRATE HEATER=heater_bed TARGET=<temp>
#
# After the autotune process completes, PID parameter results
# can be found in the Octoprint terminal tab (if you're quick)
# or in /tmp/klippy.log.
#
# Enter the PID parameters into the appropriate sections of ~/printer.cfg .
#
# * [extruder] > max_temp
# * [heater_bed] > max_temp
#
# The max temps included in this printer config are limited to 230 for extruder
# and 70 for heated bed. If your printer has been modified to handle higher temps
# (like an upgraded hot end or a separate MOSFET for your heated bed), you may
# want to increase these values.
#
# Note: Some Melzi boards were shipped with 10K pullup resistors
# instead of 4.7K. If the temperatures on your printer seem way
# off before running the PID tune, you may need to add
# "pullup_resistor: 10000" to both the extruder and the heater_bed
# config sections.
#
# * [mcu] > serial
#
# Enter the USB serial port of the printer in /dev/serial/by-id/ format
# for best results.
#
# - Power cycle the Wanhao Duplicator i3
#
# - Issue the command "RESTART" via the Octoprint terminal tab (similar to
# how you would send a manual gcode command, but send the word RESTART).
# This tells klipper to reload its config file and do an internal reset.
# You should then see a status screen appear on the printer's LCD.
#
# - Be sure to follow these instructions before attempting any prints:
# https://github.com/KevinOConnor/klipper/blob/master/docs/Config_checks.md
[stepper_x]
step_pin: PD7
dir_pin: PC5
enable_pin: !PD6
step_distance: .0125
endstop_pin: ^!PC2
position_endstop: 0
position_max: 200
homing_speed: 40
[stepper_y]
step_pin: PC6
dir_pin: PC7
enable_pin: !PD6
step_distance: .0125
endstop_pin: ^!PC3
position_endstop: 0
position_max: 200
homing_speed: 40
[stepper_z]
step_pin: PB3
dir_pin: !PB2
enable_pin: !PA5
step_distance: 0.0025
endstop_pin: ^!PC4
position_endstop: 0.5
position_max: 180
homing_speed: 2
[extruder]
step_pin: PB1
dir_pin: !PB0
enable_pin: !PD6
step_distance: .009346
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PD5
sensor_type: NTC 100K beta 3950
sensor_pin: PA7
control: pid
pid_Kp: 18.214030
pid_Ki: 0.616380
pid_Kd: 134.556146
min_temp: 0
max_temp: 230
[heater_bed]
heater_pin: PD4
sensor_type: NTC 100K beta 3950
sensor_pin: PA6
control: pid
pid_Kp: 71.321
pid_Ki: 1.989
pid_Kd: 639.210
min_temp: 0
max_temp: 70
[fan]
pin: PB4
[mcu]
serial: /dev/ttyUSB0
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 200
max_accel: 1000
max_z_velocity: 2
max_z_accel: 100
[display]
lcd_type: st7920
cs_pin: PC1
sclk_pin: PD3
sid_pin: PC0
encoder_pins: ^PA2, ^PA1
click_pin: ^!PA3